The Hafizal.com blog

Archive for the ‘CNC’ Category

A CNC machine cannot function without a program. And a program cannot make its way to the machine without an effective data transfer system. So, what are the methods of data transfer and how effective are they in conveying data from one point to the next?

Punched tape

The first data transfer method is the punched tape. It consists of a long strip of paper with holes punched in it to store data. The holes represent a set of data that tells the machine how to move and what to do.

This method has proven to be very versatile and very useful. It has proven to withstand the test of time as numerous magnetic storage devices have deteriorated over time even to the extent of being unreadable while punched tape has been shown to be fine decades and perhaps even centuries later. Repair is also not a problem as specially designed splices can put two end together virtually unchanged. Furthermore, punched tape can be visually decoded should the need arise. This means that human accessibility is also not a problem.

Floppy Disk

While punched tape is quite a long roll of paper, a floppy disk is a small magnetic storage device that is more space efficient than punched tape. It can also be used to store simple programs.

Floppy disks virtually revolutionized the way data could be stored and transferred from one point to another. It allowed users to store and transfer data faster than punched tape allowed. Furthermore, the data within a floppy could be easily edited at any point as long as you have the proper program to read it. However, this method has proven to be quite problematic in the long run as floppies have a tendency to degrade alarmingly fast. A floppy could be unreadable after only 3 years.

RS232

Sometimes the most important aspects of a subject are not immediately obvious. Keep reading to get the complete picture.

This method is actually a set of standards for serial binary signals that connects between computers, terminals, and modems. This is a fast and efficient way to transfer data.

This cable connects a CNC machine to a computer that has floppy disk support thus eliminating the need for punched tape. This allows the operator to input data remotely and even while accomplishing other tasks. However, it need to be used in conjunction with an effective data storage device so as to have backups in case of emergencies.

Networks

Networks are a set of computers that are linked together to make data sharing easier. In an industrial scenario, networks allow a number of different users to individually create a program for the machine to run on.

This method allows multiple users to access and transfer data remotely. This allows for a faster and more efficient check-and-balance system for the programmer and the data verifier. Furthermore, different parts of the program can be completed by different programmers and then compiled by one user. This makes program creation a fast and easy process.

Manual Data Input (MDI)

MDI allows users to input commands directly into the CNC machine’s memory. This may seem to be an effective way of telling the machine what to do but it actually has a lot of drawbacks to it.

Despite it being the fastest way of telling the machine what to do, it is also a very risky and tedious operation as it requires the use of the machine’s terminal. Furthermore, the construction of a program is not as fast as opposed to the network method. It only allows one user to access the machine thus making it a long and drawn-out process.

Another disadvantage that comes with MDI is that it limits the operator to only one task at a time. However, MDI allows the most control over the machine compared to other methods.

About the Author
By Anders Eriksson, proud owner of this top ranked web hosting reseller site: GVO

Have you ever asked yourself how machines in a factory know exactly when to stop making the parts they’re supposed to make? Well, this is all because of Computer Numerical Control (CNC). But to understand CNC, you have to know what Numerical Control (NC) is.

HISTORY

NC machines were first introduced after the 2nd world war as mass production became the trend. These machines were given a set of instructions in punched cards. However, these machines were hard-wired and their parameters were difficult to change.

These NC machines still required a great deal of human intervention. To illustrate this point, try to take a look at a drill press. A lot of actions have to be taken in order to manufacture a product. The process is actually so complicated that a person has to do something almost every step of the production process. This created an avenue for errors to take place as the likelihood of fatigue increased with the quantity growth.

CNC then came into the picture when computers were introduced. Punched cards were replaced by floppy disks, cables, and other software transfer media. This made it easier to manage and edit data.

Production and manufacturing were revolutionized by the increased automation of CNC machines. These machines allowed a degree of added control over the quality and consistency of the components that were manufactured without any additional strain on the operators. This reduced the frequency of errors and allowed the operators time to perform additional tasks. Furthermore, this automation allowed a greater degree of flexibility in the way components are held in the manufacturing process.

If you find yourself confused by what you’ve read to this point, don’t despair. Everything should be crystal clear by the time you finish.

With the advent of Computer Aided Manufacturing (CAM), even programming CNC machines is a snap. These programs actually take the bulk of the programming process to make the operation less tedious. However, to be an effective programmer of CNC machines, you have to know what the machine you’re working on will be doing. That is why machinists are often the best people for the job.

The ease that the machines provide is hinged heavily on the quality of the machine. Low-cost CNC machines oftentimes have many functions that have to be manually activated. High-cost machines, however, are almost fully automated. The operator only has to load or unload workpieces. Once the cycle has been initiated, the operator just has to sit back and watch for any malfunctions. The stress on the operator is so low that some even complain of boredom in the middle of a cycle.

CODING

The programming language that CNC uses is called a G-Code. These codes actually position the parts and do the work. To be able to have a machine work properly, you have to input the correct variables such as axes, reference points, the machine accessories, and whatnot. Every machine has a different set of variables so you have to be careful to take note of the differences.

Aside from the G-Code, logical commands or parametric programming can be used to make the process more time-efficient. This type of programming language shortens lengthy programs with incremental passes. A loop can also be programmed thereby removing the need for coding repetitions.

Because of these features, parametric programming is more efficient than CAM. It allows users to directly and efficiently make performance adjustments. It also allows extensions to the functionality of the machine it is running on.

And that makes CNC.

Knowing enough about CNC to make solid, informed choices cuts down on the fear factor. If you apply what you’ve just learned about CNC, you should have nothing to worry about.

About the Author
By Anders Eriksson, proud owner of this top ranked web hosting reseller site: GVO

After World War II, people realized that they have to manufacture goods at a faster rate and at a lower cost. Hence, mass production trending came to be. Those events led to the development of the Numerical Control (NC) machines which in turn led to the Computer Numerical Control (CNC).

HOW TO PROGRAM A CNC MACHINE

CNC programming uses a code similar in structure to BASIC. So, if you know how to construct a simple counting program, chances are, you already know what a G-Code looks like. However, there a few other things you have to consider before you start encoding instructions.

The first thing that you have to do is to assign values for each of the variables. These variables include the programmable motion directions (axes), and the reference point for the axes. The values that you assign to these variables dictate the movement of the machine.

The next thing that you have to do is to take into account the accessories of the machine. Many machines have accessories that are designed to enhance the capabilities of the basic device. However, using these accessories requires you to include them in the coding system. This means that if you want a more efficient machine, you will have to know the machine inside out.

READING CODES

After those steps, you have to create a subprogram that will deal with the math. This step will then allow your machine to compute the necessary variables and effectively operate without stopping to ask the operator what the limitations are.

It seems like new information is discovered about something every day. And the topic of CNC is no exception. Keep reading to get more fresh news about CNC.

To show you what these codes look like, here’s an example from Wikipedia:

#100=3 (bolt circle radius)
#101=10 (how many holes)
#102=0 (x position of ctr of bolthole)
#103=0 (y position of ctr of bolthole)
#104=0 (angle of first hole
Tool call,
spindle speed,and offset pickup,etc
G43 in some cases (tool length pickup)
G81(drill cycle)
call sub program
N50
G80
M30

Subprogram
N100
#105=((COS#104)*#100) (x location)
#106=((SIN#104)*#100) (y location)
x#105 y#106 (remember your G81 code is modal)
If #100 GT 360 goto N50
#100=(#100+(360/#101))
Goto 100

In the code above, the machine is a drill. The operator utilized a loop in order to keep the machine from stopping. The subprogram then governs the cycle of the machine. This code is still quite a simple code. Other machines require the inclusion of the maximum RPM in the coding.

An easier way of programming CNC machines would be the use of Computer Aided Manufacturing (CAM). This system takes on the brunt of programming so that it doesn’t seem so tedious and frustrating. It is still similar to BASIC.

Another programming enhancement that was developed was the parametric programs or the logical commands. These programs were designed to shorten lengthy codes in order to make them user friendly. However, these codes do not always use the same language with every machine. The language and sequence often varies depending on the typ of machine you will be working on.

The operator has to know what the machine can do or what it was made to do before attempting to program it. You should be able to visualize the machine doing what you want it to do.

But, you don’t have to be a math wizard or a programming genius. You just have to know what your machine does and what you want it to do.

If you’ve picked some pointers about CNC that you can put into action, then by all means, do so. You won’t really be able to gain any benefits from your new knowledge if you don’t use it.

About the Author
By Anders Eriksson, feel free to visit his top ranked GVO affiliate site: GVO

The following article covers a topic that has recently moved to center stage–at least it seems that way. If you’ve been thinking you need to know more about it, here’s your opportunity.

CNC machine tools are praised all over the world because of three major factors: automation, accuracy and versatility. Human (operator) intervention is reduced to minimal levels because CNC machines can run on its own after it is programmed. Also, when the program is perfected, the CNC machine can run the instructions perfectly on its own.

Remember that any CNC machine can also be programmed to do special one-time tasks such as a dry-run, which will help the operator oversee what will happen when s/he leaves the CNC machine to do its tasks alone. Accuracy also goes hand in hand with repeatability. Again, once the program is perfected, the CNC machine can perform that task PERFECTLY even until 7 or 7000 times.

Lastly, versatility also works in the form of ?task memory? that these CNC machines have. Once a program has been performed even for just one production run, it can be easily recollected the next time that the company needs the program. This saves time for setting up and loading of different programs.

The CNC sure simplifies the work of thousands of factories and machine shops worldwide. However, no matter how great CNC sounds like, it is something that doesn’t fit in some industries. Like, perhaps, in the cosmetic industry, or in the show-business. Those examples are way too obvious. On the other hand, in these two major mechanical industries, CNC is almost synonymous to ?hero?.

THE METAL INDUSTRY

Think of Metal. Metal. Perhaps the easiest metal that you can imagine is that of?a spoon. Now, imagine ANY spoon done with bare hands. After that, imagine a thousand spoons done with bare hands. It’s so tedious you might even consider suicide if you are assigned to such a job.

The metal industry has been operating on CNC for ages. In fact, if you search CNC in the internet, you will instantly find metal companies topping the list. The major CNC centers that you will find in most metal machining processes are ?CNC turning centers?, ?CNC machining centers?, ?CNC grinding centers? and ?CNC drill and tap centers?.

You may not consider everything you just read to be crucial information about CNC. But don’t be surprised if you find yourself recalling and using this very information in the next few days.

Some of the CNC programs that are connected with the metal industry are milling, drilling, reaming, boring and tapping. Moreover, any metal that has any curved side have experienced some form of knurling, grooving, turning and/or threading.

Fabrication, in manufacturing, refers to processes that are executed on thin plates/sheets. These sheets are cut, punched, and bent to form their finishing shapes. CNC also stars in almost every aspect of metal fabrication.

THE WOODWORKING INDUSTRY

While the most beautiful wood-worked products are most likely hand-made, you cannot deny that a wide array of tools and furniture HAVE to be NOT hand-made to save time and for mass production levels. There’s just too much work and not to many hands. In light with this, CNC has worked wonders for this industry.

Important woodworking processes include cutting, framing, carving and engraving. The most useful woodworking CNC product is the CNC router table. It is capable of carving elaborate 2D and 3D designs. Moreover, it is also capable of material change while repeating the same design. Since contemporary furniture is often a splash of different materials (e.g. Wood, aluminum and/or plastic), any CNC router is capable of reproducing the same design EVEN in different kinds of materials by just altering the router bit.

Although many local, middle-sized enterprise owners are skeptical about using employing CNC in their manufacturing operations, there have been many success stories to sway them to using it anyway. In the Metal and Woodworking industries, CNC has proven itself time and again to be efficient.

It saves time and efforts in production and (more importantly) back-jobs. If you’re venturing to one of these industries, remember that the word “labor” isn’t something social anymore – it’s technological. And start calling CNC your best friend.

About the Author
By Anders Eriksson, feel free to visit his top ranked GVO affiliate site: GVO

The following article covers a topic that has recently moved to center stage–at least it seems that way. If you’ve been thinking you need to know more about it, here’s your opportunity.

The normal businessman’s mind is always geared towards profit, profit, profit. No matter how much the company spends, at the end of the day, the revenues should exceed the expenses (including tax). Although innovation is a major requirement to a business’ growth, many small-time businesses just lie back in comfort. They think that as long as they’re earning and they have a steady market, it’s all right.

This holds true for businessmen who are contented with being small-time (though it’s hard to find one). However, for businesses that are aggressive towards getting ahead, acquiring a CNC machine seems to top their list of priorities.

CNC stands for Computer Numerical Control. A CNC machine is a computer “director” which is composed of machine tools that read a specific set of instructions (in G-code) and is able to ?direct? certain manufacturing tasks repetitively. The top industries that use the CNC technology are the Metal and Woodworking industries.

If you are a regular member of a techie forum for entrepreneurs, CNC may be showered with praises because of its performance. Most businessmen also swear by saving a lot of money and time when they started employing CNC technology in their production processes. However, if you are still considering CNC at the expense of the jobs of your employees, it is best that you prefer CNC at two levels: the logical level and the emotional level.

LOGIC-WISE

CNC machines do specific instructions. They will never assume anything, nor rebel against the program loaded to them. Imagine the security of knowing that you will “reap” exactly what you “sowed”. Let’s say, something goes wrong during the process. Assuming the machine is in perfect condition, you CANNOT put the blame on it because it just performed what you told it to do so.

Once you begin to move beyond basic background information, you begin to realize that there’s more to CNC than you may have first thought.

Secondly, there is the blanket of consistency. It provides a certain level of safety and ease to the head supervisor. If you have overseen the operations today, most likely, it will be exactly the same tomorrow. The feeling of knowing what to expect is always a good thing, especially when there’s money involved.

Lastly, there’s speed. CNC machines do not stop to think. After you do the thinking, they do the power-jobs that they need to do. It’s that simple. There is a minimized set-up time and back-job time pocket.

What you will find a flaw about CNC though, is that logic-wise, CNC machines cannot think of better ways to perform a task (IF there is a better way). A CNC machine is purely mechanical; when it was sold to you; the salesmen never mentioned the word ?creative? or “innovative”. I hope you did not miss that.

EMOTION-WISE

CNC machines are also assets of the company. When assets like this are purchased, there is little or no emotional investment that goes with it. You won’t even train it! It is expected to do certain tasks and that’s saving you a lot of time from all the explaining, demonstration and reminding.

Also, when a CNC machine is performing its task, it is void of any emotion. So no matter how hot the weather is, or how noisy the workplace is, the CNC machine will do its job just like any other day. It is different as compared to people – who have the tendency to space-out when doing very mechanical and tedious jobs.

Although the CNC may want to, it also cannot complain. That’s really convenient. What you will need to note now is your electric bill. Beware, for when getting CNC machines, it may betray you in the form of lofty bills. All the emotions you’ve saved might just be unleashed.

That’s the latest from the CNC authorities. Once you’re familiar with these ideas, you’ll be ready to move to the next level.

About the Author
By Anders Eriksson, proud owner of this top ranked web hosting reseller site: GVO

Do you ever feel like you know just enough about CNC to be dangerous? Let’s see if we can fill in some of the gaps with the latest info from CNC experts.

CNC has different applications depending on the machines that operate on it. So if you’re a budding operator, you should know the most common machines that can operate on CNC.

Milling

Milling machines are common CNC machines. These devices are used in the shaping of metal and other solid materials. It is basically a rotating cutter and a table. Milling machines are capable of complex toolpaths as the cutter is not limited to a sideways movement but allows for an ?in and out? motion. This movement is precisely controlled by moving the table and the cutter relative to each other. Cutting fluid is then pumped in to lubricate and cool the cut and to remove any swarth that is generated by the cut.

Lathes

Lathes are machines that perform different operations such as sanding, cutting, knurling, deformation, or even drilling. These machines work by spinning various solid objects and then using tools that are symmetric to the axis of rotation. A lathe machine has a single tool in which the workpiece is worked against the tool. The tool is then worked alongside or into the workpiece in order to generate the feed.

Lathes can be used for different operations.

Machining Centers

These are more complex CNC machines that combine milling and turning. As milling was described earlier, turning will be the focus of this section.

Turning is the process by which a central lathe is used in conjunction with the rotation of the material to be turned. The cutting tool is then moved along the two axes of motions to produce accurate dimensions.

It’s really a good idea to probe a little deeper into the subject of CNC. What you learn may give you the confidence you need to venture into new areas.

Combining turning and milling can produce extremely precise components. And that is what these machines are used for. However, due to the complexity of these machines, operators have to be specialists in order to be able to operate with maximum efficiency.

Electrical discharge machine

An electrical discharge machine (EDM) creates cavities in metals by emitting electric sparks. This process requires an electrode, coolant, a power source, and a tank. The cycle is accomplished by connecting the workpiece to one side of the power supply and then placing it in the tank. An electrode (made in the shape of the cavity required) is then connected to the other side of the power supply.

The tanks is then filled with coolant and the electrode is lowered until a spark jumps between the work and the electrode. As the coolant is a dielectric substance (resists electric currents), it requires a smaller difference in distance in order for a spark to jump through. This means that when the spark appears, the dielectric property has been overcome. The spark then dislodges material thereby creating a cavity in the shape of the electrode.

CNC systems

CNC systems are complex machines that transfer and store data regarding the operation mechanism of the machines. Motion programs include point to point control, straight cut control, and contouring control.

Point to point control means the control of the tools from one point to another in the coordinate plane. This method of control is commonly used in drilling and boring operations.

Straight cut control is the method by which a tool is moved in all axes of the machine. The tool also has the ability to move in a 45 degree angle.

Contouring control is the means to create a toolpath. It moves the tools by interpolating points or coordinates that make up the path for the tool to follow.

Now you can understand why there’s a growing interest in CNC. When people start looking for more information about CNC, you’ll be in a position to meet their needs.

About the Author
By Anders Eriksson, feel free to visit his top ranked GVO affiliate site: GVO

In the employment world, the phrase ?manual labor? is often associated with jobs which are dirty, psychologically sickening, or worse, both. Small to medium-size manufacturing enterprises are moving towards using the CNC(Computer Numerical Control) in their major manufacturing processes because of its fame in accuracy, flexibility and automation. If you’re one of these entrepreneurs, don’t jump in the bandwagon just yet.

Acquiring a CNC machine is more than just buying additional equipment; it also has a social aspect in it. Here is the low down:

PEOPLE-WISE

First, you have to consider the people who are working in your shop. How many people will be displaced if you buy a CNC machine? Keep in mind that a CNC machine is multi-operational; so it’s possible that a couple of laborers will be erased from the production team. Experts say that the healthy ratio is at least one-sixth (1/6) of your whole labor force.

You will be saving time and effort, yes, and that is the best thing about having a CNC machine. However, you might be worrying about actually terminating people because, to put it bluntly, you won’t need them anymore. A CNC machine, just like any machine, will need an operator. Instructions used by a CNC machine for operational execution are composed of CNC ?words/codes? and is in the form of a ?sentence?.

Does one of your people ever have experience with a CNC machine before? Can s/he formulate CNC instructions? If the answer to both questions are ?yes?, then that’s absolutely good news. However, if you answered ?no? to at least one of the questions, then there are more things to evaluate.

Are your people capable of fast-learning? If it pains you to terminate them because they have been good employees in the past, train them on how to use the CNC machine and how to compose instructions for it. There are plenty of free training kits online.

I trust that what you’ve read so far has been informative. The following section should go a long way toward clearing up any uncertainty that may remain.

COMPANY-WISE

There’s a corporate adage that goes: ?Innovate or die?. There’s a lot of truth in that. A purchase of any CNC machine symbolizes a company’s decision to innovate to increase productivity. However, there are a few things that you need to note.

Review your company’s history. How long should you innovate drastically in terms of production? CNC equipment is expensive. It is an investment. In the long run, you may be forced to buy new equipment more often. Consider CNC heavily if you feel that your company innovates faster than other companies in terms of the industry that you belong to. After all, you can easily alter designs and material when you have CNC powered operations.

In most companies, ?Innovation? is another word for ?saving?. It means saving time, effort and space. In using CNC machines, the first two factors are sure savings while the third is not. People doing the labor and CNC machines often occupy the same amount of space. Do not romanticize a ?clearing of clutter? effect when you buy a CNC machine. You will keep up, in terms of production; but CNC equipment also occupies a lot of space. So in that aspect, it’s pretty much the same thing.

Another thing that you have to be reminded of is the level of accuracy that your company needs to produce. Intricate patterns on metal/wood will DEMAND CNC accuracy. So any time that you feel your company is ready for such innovation and accuracy, consider employing CNC in your manufacturing.

At the end of the day, the last aspect that you need to evaluate is you, yourself. As the owner/head manager, you have to KNOW AND UNDERSTAND the CNC machine and the software well. This is the biggest battle that you have to face.

The equation to improvement is simple a really good machine plus a really good operator (you). Do not easily be blinded by the salesmen’s poetry.

Now might be a good time to write down the main points covered above. The act of putting it down on paper will help you remember what’s important about CNC.

About the Author
By Anders Eriksson, feel free to visit his top ranked GVO affiliate site: GVO

You might have not heard of the CNC before, or what it does, or how it makes lofty manufacturing operations a lot easier. However, CNC machining is dubbed as one of the most important factors of most production processes. The common tasks CNCs machines usually perform are drilling holes, tool changing, cooling and lubrication of separate factory machines at the same time.

Let’s start with a brief introduction. CNC stands for Computer Numerical Control and it has been around since the early 1970′s. Before it was christened CNC, it was called NC, for Numerical Control. When computers were introduced during 1070′s, the name changed. It has stroked almost all manufacturing forms in almost all stages of production. CNC machines either substitute some existing manufacturing processes or combine work with them.

A CNC program is just any other set of instructions. It’s written like a sentence and the order of operation is chronological. The machine will then execute that set of instructions step-by-step. A special series of CNC words/codes are used to relay what the machine is supposed to do. CNC codes begin with letter addresses (like S for spindle speed, and X, Y & Z for common linear axis motions).

When certain codes are arranged together in a coherent method, this group of CNC codes create a ?command? that is like a sentence. A common CNC machine will only be needing around 40-50 words/codes to program different commands. See, it’s not very difficult to learn.

Although CNC sounds very independent and do-it-all, there are a few words that you need to know to fully understand CNC operations.

THE CAM

It’s really a good idea to probe a little deeper into the subject of CNC. What you learn may give you the confidence you need to venture into new areas.

CAM stands for Computer Aided Manufacturing. It simplifies the programming processes which are new, and added to the CNC program regularly. Of course, the easy applications can be programmed with only the simplest machines around: the pen, paper and calculator. However, more complex programs are vital regularly. It is when composing these programs become much more tricky and (worse) tedious.

The CAM is a program that runs on a computer that aids the CNC programmer with the programming. It also works hand-in-hand with the CAD (Computer Aided Design) design drawing (those designs engineers compose/nurture). With the CAM helping, redefinition of the work-piece configuration is not needed. What the CNC programmer is left to do is just to specify the machine operations to be executed and the CAM system will compose the CNC program automatically. Thanks to CAM, programming tediousness will not be a problem to the CNC programmer again.

THE DNC SYSTEM

DNC stands for Distributive Numerical Control. It is a computer that is connected with one or more CNC machines, forming a network. When a program is manually composed and ready to be loaded to the CNC control, it is being typed right into the control. However, this is like using the CNC machine as a luxurious keyboard.

Moreover, if the CNC program is achieved with the help of CAM, it is already in text form and ready to be loaded to the CNC control. The DNC simply distributes the CNC program to more than one CNC machine. Lately, the newest controls are more advanced in terms of networking capabilities and can be networked with, say, the Ethernet.

If it’s your first time to read and learn about the CNC, it may sound so mighty and ubiquitous. It’s about time you learn they also need help from some programming friends such as the CAM and the DNC. No man is an island; but hey, neither are CNC machines.

About the Author
By Anders Eriksson, proud owner of this top ranked web hosting reseller site: GVO

When a program is completed and sent to the Computer Numerical Control Machine, the programming process is over. All calculations were made and the algorithm fully written. But the question is the programmer’s job really finished? When is the programmer’s responsibility really over? And how can we evaluate the type of program that the Computer Numerical Control Machine programmer did?

The fairest and reasonable answer to those questions would basically when a part has been machined under the most optimized working conditions. Therefore the Programmer’s responsibility does not end after he or she finishes the program. We could say that the program at this stage is still very much in the development process, because most of the programming considerations were based on certain assumptions and there are a lot of external factors that may affect the outcome of the product.

Every Computer Numerical Control programmer should have an effort to be in the touch with the actual production. In the field of software development, Constant communication with your colleagues as well as actual machine operators of the CNC will help you to improve your own program. Because most of the time the CNC machine operators are a good source of constructive ideas, improvements and suggestions.

A good CNC programmer should talk, ask questions to them and most importantly listen to what they have to say. Programmers who never put their foot in the actual machining process and think they are always right are all on the wrong track. Exchanging ideas with CNC machine operators, asking questions and seeking answers is the only way to be fully aware of what is going on in the machine.

Whenever you start a Computer Numerical Control Program the first time it is important to check its Program Integrity. A new and unproved program is a potential source of problems. During Manual Programming in CNC, mistakes are more common than when the program is made in a CAM program.

How can you put a limit on learning more? The next section may contain that one little bit of wisdom that changes everything.

A good way to look at a new program is through the machine operator’s perspective. Experienced Machine Operators take a direct approach when running a program for the first time. That means that they wont take any chances of mistakes with the actual running of a program therefore a good programmer must take note of any comments that the Machine operator will say about the program.

What does an experienced Machine Operator look for in a new part of a program? Most of the Machine operators would say that the first and most important thing to be checked on a Computer Numerical Control Program is its consistency. Therefore a machine operator looks at how a CNC programmer does its own programming, is the way you create your own algorithms the same as the other ones. Machine Operators take note with this kind of Information.

Upgrading your CNC Program

Whenever you upgrade your own program, it means that you are strengthening or enriching it, therefore making it better than it was before. Upgrading would be based on this standard, It is to decrease the production cost without compromising the quality of the part being manufactured or the safety of the Computer Numerical Control Machine Operator.

One of the Most Common forms of Program Optimization is doing some minor changes to the spindle as well as the feed rates of the machines. This process is called cycle time optimization, slightly increasing the spindle speed and feed rates of these machines will decrease the time it takes to finish the part.

And when we compare it to mass production, saving one second for each part in a batch of 3600 pieces would mean an hour saved. Efficiency in the rate of production is a very important aspect in Mass Production.

That’s how things stand right now. Keep in mind that any subject can change over time, so be sure you keep up with the latest news.

About the Author
By Anders Eriksson, proud owner of this top ranked web hosting reseller site: GVO

Have you ever wondered what exactly is up with CNC? This informative report can give you an insight into everything you’ve ever wanted to know about CNC.

If you think that you will just sit back and relax when you have a CNC machine in your shop, think again. CNC may help you speed up your operations and even make them more efficient. However, CNC is not a ?wonder robot? which will make you disregard all your employees and expect your shop to run on auto-pilot.

Though you will need more people without the CNC technology, you will need only three very, very skilled people. Call these people your friends, your team, whatever. In the long run, they might be just all you need to keep the shop in good shape.

THE PROGRAMMER

The first person is the CNC programmer. S/he is like the “playmaker”. S/he will create the programs that the CNC machines are intended to execute. Since the programs are in the form of CNC codes fabricated like sentences, he should have mastered these codes because they work like a different language. The regular CNC machine can use up to 50 codes, so that’s like learning 50 new words for the newbie.

Also, the programmer should have at least and engineering or machining degree. Remember that the CNC machine will only execute WHAT IT IS PROGRAMMED TO DO. If the program is wrong, the whole operation goes down the drain with it. Moreover,s/he should also be flexible and have a fast turn-around because a CNC machine is often used to machine a huge selection of different work-pieces.

THE OPERATOR

Hopefully the information presented so far has been applicable. You might also want to consider the following:

The second person that you need is the CNC operator. S/he will simply recheck the programs loaded to the machine and push the right buttons to get the work done. However, thinking that a CNC operator can have little or NO SKILL AT ALL is wrong. A CNC machine operator must have at least basic machining skills and s/he should have undergone some form of training to run a CNC machine.

These machines can produce very intricate motions, making it possible to make shapes that cannot be created on conventional machine tools. So, the operator should foresee this complexity and know how to cruise with it. The skills that an operator must have though, are lesser compared to the operators of conventional machine tools.

THE TECHNICIAN

The third person that will need is the CNC technician. Although this may still be the programmer, it’s more convenient to always have a technical expert on-call because in the long run, you may have more than one CNC machine and you may need to prioritize over the other in case both gets crippled at the same time. Just like the programmer, the technician should also be flexible and articulate. CNC offers a lot of complexity when it’s running right, how much more if it’s behaving badly?

So, if you are having job openings for positions that need to be handling a CNC machine, ask the applicants first to do a demo for you and make sure that during the demo, they know what they’re doing. An exam may also do wonders too. If they have no experience with any kind of CNC machine, it is advisable that you encourage them to take short courses on CNC.

Eighty-hour courses are available online and hey, it’s better than nothing. Experts even encourage employers to hire CNC machinists who have finished AND PASSED the National Occupational Competency Testing Institute (NOCTI) assessment just so they could be sure that their CNC machines will go to good hands. After all, a CNC machine is still an asset.

This article’s coverage of the information is as complete as it can be today. But you should always leave open the possibility that future research could uncover new facts.

About the Author
By Anders Eriksson, proud owner of this top ranked web hosting reseller site: GVO